|
|
发表于 2006-3-10 00:22:56
|
显示全部楼层
找有你形号的人帮你用mtkflash dump个出来.(建议不要用win 版,免得系统不隐时又死机,刷bios等等的最好还是在 real dos mode 中进行)
How to backup your firmware with mtkflash:
1.Create a boot disk or a boot CD. Or download one from >NIL's PioneerDVD Page, or digi's Page
2.Download a version of mtkflash from below (See Download)
3.Extract mtkflash to an easy to access directory such as "C:\firm"
4.Restart your computer with your boot disk/CD in the proper drive and navigate to your folder with mtkflash, "C:\firm". Only minimal boot is necessary, you do not need to boot with CD-ROM support as you will not be reading any discs with the drive. Most boot disks will not allow support for Hard Drives partitioned with NTFS.
5.Type the command now to backup your firmware: If version 1.80 or older use "mtkflash # r /b /m filename.bin" If using version 1.80.1, then do not include the /b flag! Use this command for version 1.80.1: "mtkflash # r /m filename.bin" Pay close attention to the spaces. You must replace '#' with one of the following:
'1' if the drive is Primary Master,
'2' if the drive is Primary Slave,
'3' if the drive is Secondary Master, or
'4' if the drive is Secondary Slave
Ex 1: If you wanted to use mtkflash 1.80.1 to backup the firmware from your LDW-811S hooked up as Secondary Master, then you would use this command: "mtkflash 3 r /m HS0P.bin"
Ex 2: If you wanted to use mtkflash 1.55 to backup the firmware from your LTR-52246S hooked up as Primary Slave, then you would use this command: "mtkflash 2 r /b /m 6S0F.bin"
刷回去
How to flash your drive with mtkflash
1.Create a boot disk or a boot CD. Or download one from >NIL's PioneerDVD Page, or digi's Page
2.Download a version of mtkflash from below (See Download)
3.Extract mtkflash and the binary firmware file to an easy to access directory such as "C:\firm"
4.Restart your computer with your boot disk/CD in the proper drive and navigate to your folder with mtkflash, "C:\firm". Only minimal boot is necessary, you do not need to boot with CD-ROM support as you will not be reading any discs with the drive. Most boot disks will not allow support for Hard Drives partitioned with NTFS.
5.Type the command now to flash the firmware: If you're using version 1.80 or older use "mtkflash # w /b /m filename.bin" If using version 1.80.1, then do not include the /b flag! Use this command for version 1.80.1: "mtkflash # w /m filename.bin" Pay close attention to the spaces. You must replace '#' with one of the following:
'1' if the drive is Primary Master,
'2' if the drive is Primary Slave,
'3' if the drive is Secondary Master, or
'4' if the drive is Secondary Slave
Ex 1: If you wanted to use mtkflash 1.80.1 to flash a binary version of the HS0P firmware onto your LDW-811S hooked up as Secondary Master, then you would use this command: "mtkflash 3 w /m HS0P.bin"
Ex 2: If you wanted to use mtkflash 1.55 to flash a binary version of the 6S0F firmware onto your LTR-52246S hooked up as Primary Slave, then you would use this command: "mtkflash 2 w /b /m 6S0F.bin" |
|
狗仔卡
发表于 2006-3-5 21:56:17
恢复卡