|
|
发表于 2002-10-25 20:47:50
|
显示全部楼层
最初由 xyc2000 发布
[B]为什么没人推荐迈拓，迈拓的非常不错！ [/B]
转贴：迈拓硬盘也存在质量问题！！
注意:所有这些出现问题的硬盘基本上都发生在购买后使用期在一年到一年半的迈拓硬盘上,并且SMART的错误提示均出现在对硬件要求很严格的主板上如华硕等.
请大家注意了，步IBM的后尘，如今全国公认比较稳定的迈拓硬盘也存在质量问题，症状如下：
1.最先出现的征兆是硬盘开机找不到,重新启动后可以找到并正常使用,没有任何错误提示
2.上面的状况时断时续出现近一个月左右后,开机的自检出现如下提示:
SMART Failure Predicted on priamry Master:maxtor 5T040H4
warning:immediately back-up your data ,and replace your hard disk drive.
A Failure may be imminent.
(5T040H4是我的硬盘编号是金钻6代40G的 ,其他的编号见官方站点)
但是按F1以后可以正常进入系统,并且没有任何坏道及不正常现象
大家可以使用迈拓官方的检测软件powermax3.04(http://www.mydrivers.com/dir53/d21204.htm)来测试一下自己的硬盘.
根据gagu兄提供的powermax原文说明(如下)
PowerMax Error Codes - What does it mean?
Description
This document describes Maxtor's PowerMax diagnostic / error codes and the action a user should take when a failure condition is encountered.
Note: Do not run PowerMax from within a GUI environment (ie from a Windows desktop window), as this can make the test results inaccurate. Please
remove any other hard drives you might have in your system which you don't want to test and overwrite.
Answer
When the PowerMax diagnostic is executed and encounters a failure condition during testing, it will display a six or three digit alphanumeric diagnostic
code. The six digit validation codes were added to the program for end-user warranty replacement purposes only.
Users with Six Digit Error Codes:
l If you receive a six digit error code with an S57 at the end (xxxS57), it is recommended that you run the Write Disk Pack (Low-Level Format)
option from the PowerMax utility.
Warning: The write disk pack option will erase all data on the drive, so please backup all your data before choosing this option.
Note: When running the 90-second quick test, we have found that the S57 error code may display even if there is no actual failure within the
drive. This is a problem with the PowerMax diagnostic software and is currently being investigated for a future fix. If the Write Disk Pack option
(low-level format) is executed successfully, and the error code with S57 still appears after re-running PowerMax, then the code is valid and the
drive should be replaced.
l If you receive a six digit error code with an MX1 (xxxMX1) at the end, this means that either the drive is not supported by PowerMax or you should
try testing the drive on another IDE/ATA bus.
l All other six digit error codes indicate that the drive should be replaced. The PowerMax diagnostic will typically provide a short description
regarding the test that failed. However, there are no "user-serviceable" or field replaceable parts on the hard drive. Therefore all drives with a valid
six digit code should be replaced.
For information on warranty status and drive replacement (RMA) please visit our
Warranty Information Page
Users with Three Digit Error codes:
Three digit error codes refer to issues other than the drive. Please refer to the table below.
Error Code Action
004* Cabling/Jumper Configuration Problems
005* BIOS doesn't support capacity and/or LBA not enabled in BIOS.
006* No Partition Detected
笔者将上述说明中的重要部分翻译过来以方便大家
这个文档描述了Maxtor的Powernax diagnostic的错误代码和当出现错误时用户该怎么做。
注意：不要在图形界面下（如windows的桌面环境）运行PowerMax，它会使测试结果不准确。请从您的系统中移除其它的你不想进行测试和写操作的硬盘驱动器。
解决方法
出现六个数字错误代码：
如果你得到一个以S57结尾的六位数字错误码（如xxxS57),强烈推荐您运行Write Disk Pack操作（即低级格式化）
警告：Write Disk Pack指令会擦除所有的硬盘数据，所以请先备份您的数据。
注意：当运行90秒快速测试时，我们发现即使驱动器没有真正的错误S57的错误代码会出现。这是PowerMax diagnostic 软件的一个错误，现在正在研究来找到一个修补的办法。如果低格操作成功执行完毕了，再次运行PowerMax仍然会出现错误代码，那么这个错误代码是有效的，这个磁盘需要替换。
如果您得到一个以MX1结尾得六位数字代码（如xxxMX1),这意味着PowerMax不支持这个驱动器，或者是您正试着在其它的ide/ATA总线的驱动器上使用本软件。
所有的六位数字错误代码预示着这个驱动器将要被替换。针对失败的测试PowerMax diagnostic会给出一个简短的描述。
出现三个数字的错误代码：
004* 接线或跳线设置错误
005* BIOS不支持该容量或/和未使用LBA模式
006* 未发现分区
后注:即便是能够正常使用并且没有坏道或是任何提示,笔者认为这块硬盘已经存在质量问题,至于什么时间才真正废掉还有待时间证明.
笔者在进行了一个半小时的低格后检测仍然有T4HS57的错误代码,powermax的smart检测还是失败,除了更换硬盘笔者实在无法找到更好的解决办法了. |
|
狗仔卡
恢复卡